Copyright 2018 IC Realtime All rights reserved. IC Realtime IC Realtime IC Realtime IP Camera Static Models 04/01/2019 2:01 PM 04/01/2019 2:01 PM 204 devices_sm\camera_sm.gif devices_lg\camera_lg.gif lua_gen ip DriverWorks IC Realtime:camera camera SNAPSHOT, MJPEG, H264, H264I False False False False False False False 0 80 554 True DIGEST admin admin True True False False 5001 6 Camera 2 False False False False CAMERA 6001 1 Ethernet 4 True False False True TCP 80 True True AlwaysOn 0 0 False FOR IC Realtime STATIC CAMERAS This driver enables images from IC Realtime IP cameras to be displayed on the Control4 UIs. The IC Realtime cameras are SDDP enabled which allows them to be identified on the system and the driver automatically added to the project. ---------------------------------- HARDWARE SET UP Ensure that the camera has the right firmware installed. ---------------------------------- CONTROL CONNECTION SET UP SDDP If the camera was added to the project via SDDP then the control connection will have automatically been set up. Check to ensure that the camera is on the same IP subnet as the Control4 system. Manual We recommend that the camera be identified by SDDP. However you can also manually identify the camera via the Connections - Network tab. To identify the camera, you should trigger video tampering to let the camera send the identify message.(make sure that the camera's video tamper function is enable.you can enable the function via the camera's web page - Event - Video Detect - Video Tamper tab) ---------------------------------- PROPERTIES * SerialNumber - It will show the camera's SerialNumber. * Camera Model - It will show the camera's Camera Model. * Firmware - It will show the camera's Firmware. * Motion - The value of this property mean: if the value is not 0, for example the value is 3, the dirver would check the camera's motion state evenry 3 second. if the value is 0, it mean disable this function. (To use this function, ensure that the motion detect function is enable. you can enable this function via the camera's webpage - Setup - Event - Video Detect - Motion Detect tab, also in this tab, you can change the areas and schedules about the motion detect.) * Brightness,Contrast,Saturation,Sharpness - Change these values, it will change the camera's value about Brightness,Contrast,Saturation and Sharpness. * Debug Level and Mode are for testing purposes. ---------------------------------- ACTIONS A number of actions are available to assist with the setup of the driver. * Reboot Camera - Will cause the camera to reboot - It may be several minutes before the camera is back online. * Toggle Mirror - Allows you to toggle image mirroring - useful if the camera was physically installed incorrectly. * Sync Time - Will synchronize the camera time to the controller's time. ---------------------------------- LIMITATIONS & GOTCHAS * This driver is for IP cameras only; not the NVR. Address each camera sepearately using these drivers - do not try and address the NVR with this driver. * Not all features are available on all cameras. ---------------------------------- TROUBLESHOOTING If communication cannot be established with the camera then this is likely to be caused by one of the following: * Incompatible camera firmware - ensure camera is running latest firmware * Camera not on same IP subnet as Control4 controller. * If manually entered IP address then this is incorrect * Contacts not bound correctly to Control4 contact devices. ---------------------------------- CUSTOM PROGRAMMING As well as the standard Control4 programming actions the following are available: MIRROR/UNMIRROR IMAGE REBOOT_CAMERA DAY_NIGHT NOISE_REDUCTION_3D WHITEBALANCE BRIGHTNESS CONTRAST SATURATION SHARPNESS NOTE: Not all cameras will support all these functions. ---------------------------------- SUPPORT Please give a detailed description of the problem. Please also include the version number of the driver and the version of Control4 OS that you are using and the firmware of the camera. ---------------------------------- Sync Time Time Toggle Mirror Mirror Reboot Camera Reboot MIRROR_IMAGE Mirror image on NAME UNMIRROR_IMAGE UnMirror image on NAME REBOOT_CAMERA Reboot camera on NAME DAY_NIGHT Set Day/Night to PARAM1 on NAME Type LIST False 0 - Color 1 - Auto 2 - Black/White NOISE_REDUCTION_3D Set 3D Noise Reduction to PARAM1 on NAME (the 0 value means close the 3D Noise Reduction) Value (0-100) RANGED_INTEGER False 0 100 BRIGHTNESS Set BRIGHTNESS to PARAM1 on NAME Value (0-100) RANGED_INTEGER False 0 100 CONTRAST Set CONTRAST to PARAM1 on NAME Value (0-100) RANGED_INTEGER False 0 100 SATURATION Set SATURATION to PARAM1 on NAME Value (0-100) RANGED_INTEGER False 0 100 SHARPNESS Set SHARPNESS to PARAM1 on NAME Value (0-100) RANGED_INTEGER False 0 100 WHITEBALANCE Set WHITEBALANCE to PARAM1 on NAME Type LIST False Auto Sunny Night Outdoor Version STRING true Lua Error Driver Information STRING true SerialNumber STRING true Camera Model STRING true Firmware STRING true Motion RANGED_INTEGER false 0 0 10 Brightness RANGED_INTEGER false 50 1 100 Contrast RANGED_INTEGER false 50 1 100 Saturation RANGED_INTEGER false 50 1 100 Sharpness RANGED_INTEGER false 50 1 100 Debug Level LIST false 2 - Warning 0 - Alert 1 - Error 2 - Warning 3 - Info 4 - Debug 5 - Trace Debug Mode LIST false Off Off Print Log Print and Log Camera 1 Motion Start When NAME Motion is Started 2 Motion Stop When NAME Motion is Stoped